Transferring fluids in health care applications can be a complicated procedure when trying to ensure there is no contamination from outside surfaces. Pinch valves offer a solution via a pinching mechanism that “pumps” the fluid through the tubing. This article examines the technology, offers considerations for selection, and highlights the types of tubing that are best suited for use.
Many medical applications require transferred fluid to be isolated from external contamination. In these situations, valve choice is critical to creating a contamination-free device. Isolation valves, which cause the transferred fluid to contact valve components, require cleaning and flushing. In contrast, pinch actuators, commonly referred to as “pinch valves,” use disposable thermoplastic medical tubing that is easily replaced and threaded through the pinch valve’s head assembly.
Pinch valves are available in a variety of sizes, actuation types (pneumatic or electric) and pinching mechanisms. There are a variety of important design and material considerations when selecting the type of pinch valve to use.
Chart 1: Pinch Valve Actuation Type Considerations
Electric Versus Pneumatic Actuation
Engineering and operational tradeoffs often drive the selection of actuation type (Chart 1). For example, for fluids moving at high pressure and flow rates, a pinch valve with stronger closing force is required. Pneumatic pinch valves work at high operating forces, although they can also function at low pneumatic pressures. In general, pneumatic pinch valves provide more design freedom and fewer engineering considerations than electric pinch valves. However, a pneumatic compressor or an alternative compressed air source is required.
|Electronic pinch valve
Increased tubing diameter requires the actuator to have a longer stroke length to completely pinch the tubing closed. This becomes a critical factor when comparing pneumatic and electric pinch valves. As the operating stroke length increases, so does the size of the solenoid needed to provide the necessary closing force. Larger solenoids increase power consumption and the need to disperse additional generated heat.
The need to maintain a normally open or closed “fail safe” position also differentiates pneumatic and electric pinch valves. For electric actuators, holding the pinch valve in a powered position (either open or closed) can considerably increase power consumption and heat generation. A latching valve can address this issue. Latching valves include a circuit that activates a “magnetic latch,” which holds the valve in the desired open or closed position, and then shifts electricity to the solenoid. In the latched position the valve is held in place—either open or closed—and the power to the solenoid is shut off so that it does not overheat and burn out. Then a separate circuit is activated to release the latched position.
Solenoid power and size requirements are affected by the required duty cycle (cycle rate and typical on/off time). Generally, a high duty cycle (the solenoid opening and closing at a high frequency) increases power consumption and generates more heat.
Chart 2: Medical Tubing Characteristics
Properties of elastomeric tubing (Chart 2), such as its durometer (flexibility) and chemical resistance, impact both the demands of the pinch valve, as well as the sterilization method utilized. Exposure to lower temperatures can also stiffen some medical grade tubing, requiring a pinch valve with higher closing force to completely pinch the tubing closed.
|Pneumatic pinch valve|
Silicone tubing remains extremely pliable and elastic across a wide variation in temperature. Standard for medical applications, silicone tubing meets most requirements for cleanliness and non-toxicity.
Polyurethane tubing also remains flexible across a wide range of temperatures. It is flexible, tough tubing that is available in a wide variety of durometers. It has excellent resistance to “flex fatigue” and returns to its original dimension upon release.
Medical polyvinyl-chloride (PVC) tubing is available in a variety of durometers. Its smooth surface maximizes flow and prevents sediment accumulation. It also withstands repeated sterilization, should this unique characteristic be beneficial to the application.
A pinch valve is an excellent solution to ensure sanitation and ease of changeover between procedures to ensure contamination-free fluid management. However,
|Pinch valve design complete with the cylinder, plunger, and back stop. Bimba can design a custom pinch valve that will suit custom applications as well.|
medical equipment design engineers need to consider many variables to ensure success.
Don Harris is a product marketing manager for Bimba Manufacturing, a leading supplier of pneumatic, hydraulic, and electric solutions. He is currently spearheading the company’s industry focus into the medical market segments.