Advertisement

Motion Control Coating

January 18, 2007 11:36 am | Kerk Motion Products | Product Releases | Comments

Superior performance lead screw, linear rail, spline shaft, and ScrewRail actuator assemblies are all offered with Kerkote TFE coating.

LISTED UNDER: Ball and Lead Screws | Device Coating

Laser Modules

January 18, 2007 11:36 am | Edmund Optics | Product Releases | Comments

These laser diode modules are well-suited for integration by OEMs because they produce high-quality beams at low cost. The modules can be used in medical, industrial, and R&D environments.

LISTED UNDER: Laser Micro-Machining | Product R&D

Collaborative R & D Website

January 15, 2007 10:51 am | Product Releases | Comments

A website has been launched that brings together university students and industry that have common interests in R&D. The site allows industry to post projects that they are looking for university students to work on for their senior design project.

LISTED UNDER: Product R&D
Advertisement

Multiphysics Tutorial CDs

January 15, 2007 10:51 am | Product Releases | Comments

Engineers and scientists from all areas and disciplines can get a quick overview of the power and benefits of modeling, simulation, and virtual prototyping thanks to a series of free multiphysics tutorial CDs from Comsol.

LISTED UNDER: Prototyping

Injection Molded Plastic Prototypes

January 11, 2007 8:17 am | Proto Labs, Inc. | Product Releases | Comments

This company can turn 3D CAD models into real plastic parts in as few as three days. Injection molded in a choice of engineering-grade resins, these plastic parts are ideal for functional testing, bridge tooling, or even short-run production.

LISTED UNDER: Rapid Prototyping

Fastener Coating

December 5, 2006 12:21 pm | Nylok Corp. | Product Releases | Comments

There is no need for gasket seals or sealant compounds or any other time-consuming in-house assembly sealants.

LISTED UNDER: Fasteners | Device Coating

Gas Plasma System (3609)

December 5, 2006 12:21 pm | Plasmatech, Inc. | Product Releases | Comments

This low pressure gas plasma system is for thin film coating and surface modification of medical components. The cleanroom-compatible AL140 plasma system has a 850 x 450 x 350 mm aluminum chamber.

LISTED UNDER: Surface Modification | Control | Flow

Low Cost Motor Resolves Coating Challenge

December 5, 2006 12:19 pm | Elliptec Resonant Actuator Ag | Product Releases | Comments

After an introduction of the basic technology of the Elliptecmotor, this article will present the physical analysis necessary for understanding the operation of the motor and will discuss its use in vacuum conditions. The technology can be utilized to address concerns with physical vapor deposition.

LISTED UNDER: Permanent Magnet Motors | Actuators | Wire and Cable
Advertisement

Software Solutions: Building Blocks for FDA Compliance

December 5, 2006 10:48 am | Syspro | Product Releases | Comments

Many medical device manufacturers have discovered that their choice of ERP

LISTED UNDER: Compliance Software | Injection Molding | Medical Device Testing

Injecting Design Into the Molding Process

November 10, 2006 10:24 am | Amoebic Inc | Product Releases | Comments

There are a number of factors medical device manufacturers need to consider when using injection molded parts in their device. If they don’t, they may be caught by surprise when they think they are ready to move into full production on a part.

LISTED UNDER: Injection Molding | Injection Molding | Thermoplastics Molding

Innovations Series Presents: Scoping New Technologies

November 10, 2006 10:24 am | Product Releases | Comments

On the cover: Smith & Nephew's Condor System functions as a command center for the Digital OR. It offers voice-activated control. (Photo: Smith & Nephew)   Minimally invasive procedures offer tremendous advantages over more traditional techniques.

LISTED UNDER: Product Design

Micro-Abrasive Blasting

November 6, 2006 11:11 am | Product Releases | Comments

Micro-abrasive blasting is a simple, yet highly effective, method to clean, cut, deburr, or texture a wide variety of surfaces.

LISTED UNDER: Surface Modification | Micro Molding

Liquid Injection Molding

November 6, 2006 5:02 am | Rubber Industries | Product Releases | Comments

Limfast Liquid Injection Molding is a service offered for molding custom medical liquid silicone rubber components and bonded Silicone to metal or plastic components, delivered in prototype quantities within 10 working days.

LISTED UNDER: Injection Molding | Injection Molding | Silicon Molding

I.V. Drug Delivery Takes Another Evolutionary Step

October 13, 2006 9:50 am | Hospira, Inc. | Product Releases | Comments

I.V. containers have not experienced significant change since the introduction of plastic to replace glass in the 70s. This I.V. bag offers a variety of features that address many concerns healthcare providers have with today’s more traditional options. Hospira Inc.

LISTED UNDER: Transfer Devices | Full Service Contract Manufacturing

Plasma Processing System

October 13, 2006 9:46 am | March Plasma Systems, Inc | Product Releases | Comments

The Flextrak Plasma Processing System improves the reliability and quality of medical devices through surface modification and ultra-cleaning. The plasma processes improve the bond uniformity and adhesion between dissimilar materials, enhancing the performance of end products, such as stents.

LISTED UNDER: Surface Modification | Surface Modification

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading