Advertisement
Thermal Management

Heat Sink Attachment System

May 28, 2015 6:54 pm | by Advanced Thermal Solutions | Product Releases | Comments

The new clipKIT is a heat sink attachment system that can be used with most industry standard, off the shelf straight fin, pin fin, cross cut or slant fin heat sinks. The new system improves on heat sink performance in thermal transfer, and vibration and shock...

LISTED UNDER: Heat Exchangers

Microporous Copper Foam

April 22, 2015 11:06 am | by Goodfellow Corporation | Product Releases | Comments

Goodfellow offers a new copper foam with pore sizes between 300 and 600µm and a relative density of around 37%, providing a much higher surface area than traditional copper foams. This microporous material is expected to be of particular interest to design...

LISTED UNDER: Services | Heat Exchangers | Microporous

Zipper Fin Heat Sinks

March 10, 2015 7:02 pm | by Advanced Thermal Solutions | Product Releases | Comments

New zipper fin heat sinks from Advanced Thermal Solutions, Inc. (ATS) are protecting thousands of components from the dangers of excess heat at a lower cost than other high fin density heat sink types. Zipper fins are machined from thin sheet metal, typically aluminum or copper...

LISTED UNDER: Fans
Advertisement

Push Pin Heat Sinks

December 4, 2014 6:14 pm | by Advanced Thermal Solutions | Product Releases | Comments

With 108,000 possible configurations, Advanced Thermal Solutions, Inc. (ATS) now provides the widest choice of push pin-mounted heat sinks for cooling BGAs and other hot components. More than 200 ATS heat sinks are available with convenient push pin mounting. The lightweight aluminum heat sinks include straight fin, cross-cut, and ATS maxiFLOW spread fin geometries. More than 100 fine- pitc...

LISTED UNDER: Area (Surface) Heater

Chillers and Heat Exchangers

October 7, 2014 8:30 am | by MDT Staff | Product Releases | Comments

Advanced Thermal Solutions, Inc., ATS, has introduced a series of portable Chiller Systems and liquid-to-air Heat Exchangers for controlling fluid temperatures in looped liquid cooling systems. The new chillers allow precise temperature control of the...

LISTED UNDER: Heat Exchangers

Line Heating Control System

August 19, 2014 2:07 pm | by MDT Staff | Product Releases | Comments

Watlow integrated its components into a customizable, application-specific system consisting of: An EZ-ZONE RM temperature controller...

LISTED UNDER: Area (Surface) Heater

Highly Conformable TIM

August 15, 2014 2:33 pm | by MDT Staff | Product Releases | Comments

Fujipoly announced the expansion of its Sarcon XR-Pe product offering with the availability of a 1.0 mm thick sheet. Sarcon XR-Pe delivers a remarkable thermal conductivity of 11 W/m°K (ASTM D 5470) with a thermal resistance as low as .06°Cin2/W...

LISTED UNDER: Heat Exchangers | Conductive

Compressible Phase Change Thermal Interface Pad

June 17, 2014 9:56 pm | by MDT Staff | Product Releases | Comments

AI Technology has introduced COOL-GUMPAD CGP7156, a new class of thermal interface material with extreme compressibility to fill in all uneven and unparallel thermal interface surfaces in LED luminaire modules...

LISTED UNDER: Heat Exchangers
Advertisement

Easy Handling Thermal Compound

June 4, 2014 6:08 pm | by MDT Staff | Product Releases | Comments

SARCON SPG-30A from Fujipoly is an ideal thermal interface option for circuit boards with a large surface area, many components and delicate solder points...

LISTED UNDER: Heat Exchangers | Silicone

Filter Fans

May 20, 2014 8:00 am | by MDT Staff | Product Releases | Comments

EIC Solutions, Inc., a leading manufacturer of thermoelectric air conditioners, electronic enclosures and transit cases, has introduced a line of filter fans which provide an effective, economical method for removing unwanted heat from electrical/electronic...

LISTED UNDER: Fans

Programmable HPLC Column Chiller/Heater

April 30, 2014 8:11 am | by MDT Staff | Product Releases | Comments

Torrey Pines Scientific, Inc. announces its new EchoTherm Model CO50 Programmable HPLC Column Chiller/Heater. The CO50 has a temperature range from 4.0°C to 100.0°C readable and settable to 0.1°C. The PID control software...

LISTED UNDER: Area (Surface) Heater | Chillers/Coolers

Cartridge & Immersion Heaters

April 23, 2014 4:17 pm | Hotwatt, Inc. | Products

Cartridge heaters provide localized heat to restricted work areas requiring close thermal control. Dies, platens and a variety of other types of processing equipment are efficiently heated. Closely controlled work temperatures up to 1400º F (760º C) are obtained by a combination of heater location and proper wattage output. Immersion heaters are ideally suited for heating various liquids. They are available in various sheath materials and watt densities tailored for your specific applications. Units may be supplied for single, three phase or three heat operation. The lead end of the unit may be sealed for extreme environmental conditions.

LISTED UNDER: Heating Elements

Crankcase Heaters

April 23, 2014 4:15 pm | Hotwatt, Inc. | Products

Crankcase heaters are used to overcome the problem of migration and condensation of refrigerant in the crankcases of compressors used in air conditioning and heat pump systems. They are designed to keep the crankcase oil at a temperature higher than the coldest part of the system to prevent migration. They are constructed of the highest quality corrosion resistance materials and sealed against moisture.

LISTED UNDER: Heating Elements

Ceramic Heaters

April 23, 2014 4:15 pm | Hotwatt, Inc. | Products

Ceramic heaters are a ceramic body encasing a resistance element and packed within magnesium oxide. Temperatures to 1300°F (705°C) for applications like copiers, dehumidifiers, glue guns, heat sealing tools, instrumentation, resisters, soldering and de-soldering equipment and valve heaters.

LISTED UNDER: Heating Elements

Band Heaters

April 23, 2014 4:13 pm | Hotwatt, Inc. | Products

Band heaters are used in multiple applications like cylinders, dies, drums, holding tanks, injections and blow molding machines, and Plastic Extruders as well as many other applications. The Hotwatt Standard Band Heaters are manufactured in one or two piece constructions with maximum inside diameters of 11 1/2" and 22 1/2" respectively. Three or more sections are employed when heaters of larger diameters are needed (as for blown film extrusion dies).

LISTED UNDER: Heating Elements

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading