Advertisement

Air Process Heaters

April 23, 2014 11:38 am | Hotwatt, Inc. | Products

Air Process Heaters are used for: Baking, Drying, Laminating, Metal Working, Packaging, Plastic Welding, Preheating, Sealing, Soldering, Shrink Fitting, and Synthetic Fabric Sewing. Air Process heaters will provide hot air and gas up to 1400º F (760º C) with infinite control by varying the voltage and air flow. Units are fitted with a tubing "T" for convenient power lead outlet, while larger diameters can be supplied with post terminals on the sheath for direct electrical connections. For easier installation, Hotwatt can supply male or female NPT threaded fittings, hose adaptors (entry only), flanges, or custom fittings to your specifications. We can also provide temperature sensing control.

LISTED UNDER: Heating Elements

Heat Sinks

April 21, 2014 9:48 am | by MDT Staff | Product Releases | Comments

Crydom, a brand of Custom Sensors & Technologies (CST), announces the availability of 4 new Heat Sinks designed specifically for use with single, dual and 3-phase Solid State Relays. The new models, rated at 0.25, 0.36. 0.7, and 1.0 degrees C...

LISTED UNDER: Heat Exchangers

Thermal Interface Material

April 21, 2014 9:38 am | by MDT Staff | Product Releases | Comments

AI Technology, Inc. (AIT) introduces COOL-PAD CPR7154, a new class of thermal interface material that dispenses like a thermal pad, but performs with characteristics like that of a grease or gel when device temperatures increase to above 45°C...

LISTED UNDER: Heat Exchangers
Advertisement

New Low Resistance TIM Delivers 6.0 W/m°K Performance

September 18, 2013 3:50 pm | by MDT Staff | Product Releases | Comments

Fujipoly has announced the introduction of Sarcon GR45A-00 a very low modulus thermal interface material with a low thermal resistance. This new formulation completely fills air gaps between components, board protrusions and recessed areas while exhibiting very low pressure.

LISTED UNDER: Heat Exchangers

Aluminum Nitride Heater Exhibits New Heating Technology

August 28, 2013 3:08 pm | by MDT Staff | Product Releases | Comments

Durex Industries recently announced successfully developing an Aluminum Nitride (AlN) Ceramic Heater technology with an embedded Tungsten RTD sensor. This RTD sensor provides the fastest possible heater measurement and response to changes in temperature.

LISTED UNDER: Heating Elements

Thermal Gel Sheets: A Cooling Influence on LED Lighting

August 12, 2013 3:06 pm | by MDT Staff | Product Releases | Comments

Over the last several years hundreds of major electronics manufacturers have expanded their use of LED lighting to enhance both product appearance and functionality. Recent design trends have integrated LED lighting packages in thousands of consumer and industrial electronic platforms...

LISTED UNDER: Lamps and Lights | Heat Exchangers

Electric Heaters and Temperature Sensors

May 9, 2013 2:24 pm | Products

Durex Industries is an ISO 9001:2008 certified manufacturer of custom electric heaters, temperature sensors, temperature controls and process systems for all thermal process applications in the semiconductor, medical, plastics, packaging, adhesives, foodservice, aerospace, steel production, and power generation industries. Durex provides engineered designs from concept and prototype through production. Special testing and services include full x-ray analysis, temperature calibration, life cycle testing, FEA analysis, helium leak tests, and thermal imaging.

LISTED UNDER: Probes | RTDs | Thermocouple

Sanitary Temperature Control Systems

May 3, 2013 5:28 pm | by MDT Staff | Mokon | Product Releases | Comments

Mokon is producing high quality heating and cooling systems that provide precise temperature control of process fluids in sanitary environments. Typical applications include: electronic circuit boards and components, biotechnology and pharmaceutical, medicine and vitamin packaging, and surgical equipment and devices.

LISTED UNDER: Heating Elements
Advertisement

Form-in-Place Thermal Compound

March 5, 2013 10:32 am | by MDT Staff | Product Releases | Comments

Fujipoly announces the introduction of SARCON® SPG-20A, an easy to dispense, low-viscosity thermally conductive silicone compound. When applied between a heat-generating component and a nearby heat sink or spreader, the very low compression, form-in-place material completely fills all unwanted gaps up to 3.0 mm in height.

LISTED UNDER: Heat Exchangers | Silicone

Heat Sinks for LED Modules

February 7, 2013 4:55 pm | by MDT Staff | Product Releases | Comments

Ohmite Manufacturing, a leading provider of thermal solutions and resistors for high current, high voltage and high energy applications, introduces a new line of heat sinks for single LED power modules.

LISTED UNDER: Lamps and Lights | Heat Exchangers

Thermal Gel Sheets

January 30, 2013 10:16 am | Product Releases | Comments

Fujipoly announces the availability of Sarcon® 50GR-Ae, an extremely soft 0.5-mm thick thermal interface material. The gel-like sheet compound is designed to efficiently transfer heat from its source to a nearby heat sink.

LISTED UNDER: Heat Exchangers | Silicone

Breakthrough Thermal Technology

December 6, 2012 9:30 am | Thermacore, Inc. | Product Releases | Comments

Thermacore, Inc., a leading provider of advanced thermal solutions, is offering a new generation of compact, custom-built, high-performance air-cooled heat sinks, the result of a multimillion-dollar development contract...

LISTED UNDER: Heat Exchangers

Thin-Film Thermoelectric Modules Offer Higher Cooling Capacity

November 14, 2012 10:09 am | Product Releases | Comments

Nextreme Thermal Solutions, the leader in micro-scale thermal management and power generation solutions, today announced a new series of thin-film thermoelectric modules that offer higher cooling capacity...

LISTED UNDER: Heat Exchangers

Versatile Low Hardness Sarcon Thin Film

September 25, 2012 11:29 am | Product Releases | Comments

Sarcon 30QR from Fujipoly is a low hardness thermal interface material that exhibits a thermal conductivity of 1.10 W/m°K and a thermal resistance of .57 °Cin2/W. This material is available in roll or sheet form and can easily be die-cut...

LISTED UNDER: Heat Exchangers

550°F Bench Oven

August 9, 2012 10:00 am | The Grieve Corporation | Product Releases | Comments

No. 983 is an electrically-heated 550°F(~287.78°C) bench oven from Grieve, currently used for curing medical instruments.  3KW are installed in Incoloy sheathed tubular heating elements. Workspace dimensions are 26” wide x 22” deep x 16” high.

LISTED UNDER: Ovens | Heating Elements

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading