Advertisement

Heat Resistant Epoxy Adhesive Developed for High Performance Structural Bonding

July 14, 2010 8:06 am | Master Bond, Inc. | Product Releases | Comments

Master Bond Polymer Supreme 46HT-2 was developed for outstanding, high performance bonding strength to both similar and dissimilar substrates.

LISTED UNDER: Epoxy

Epoxy Packaging Is Well Suited for Small Applications

July 8, 2010 6:04 am | Product Releases | Comments

Packaging for reactive adhesives, sealants, or resins in small two-part epoxy delivery systems requires only a minimal amount of material to be dispensed at one time.

LISTED UNDER: Epoxy

One Part High Strength Epoxy Has High Thermal Conductivity

June 14, 2010 6:31 am | Master Bond, Inc. | Product Releases | Comments

Master Bond Polymer Adhesive Supreme 10AOHT-LO is a single component, no mix, thermally conductive compound featuring superior electrical insulation and toughness.

LISTED UNDER: Epoxy
Advertisement

Surgical Drape Tapes and Incise Film Solutions Satisfy Challenging Application Requirements

June 9, 2010 2:14 am | Vancive Medical Technologies™ | Product Releases | Comments

A broad range of incise films and bordering, assembly, fenestration and fixation tapes are now available from Avery Dennison Medical Products (MD&M East Booth 1543).

LISTED UNDER: Tapes | Films

Epoxy Has Outstanding Electrical Properties and Chemical Resistance

June 3, 2010 6:35 am | Master Bond, Inc. | Product Releases | Comments

Master Bond EP17HT-3 is a one-part epoxy that sets up in 20 to 30 seconds and snap cures in only two to three minutes.

LISTED UNDER: Epoxy

Toughened, Light Cure Adhesives Bond Instantly to a Wide Variety of Substrates

June 2, 2010 6:04 am | Product Releases | Comments

For bonding applications that must withstand impact or flexing, Henkel Corp. has introduced two Loctite Flashcure light cure cyanoacrylate instant adhesives.

LISTED UNDER: Lamps and Lights | UV-or Light-Cure

Pressure Indicating Sensor Film Increases Bond Strength

April 6, 2010 5:08 am | Product Releases | Comments

Ultrasonic welding uses high-frequency ultrasonic acoustic vibrations to create solid-state welds, and does not introduce contaminants into the weld, meaning that the machines can be specified for use in cleanrooms.

LISTED UNDER: Films | Films | Pressure

Epoxy System Ideal for Casting, Bonding, and Sealing

April 6, 2010 5:08 am | Master Bond, Inc. | Product Releases | Comments

This two part epoxy resin system that features low to moderate viscosity is well suited for potting, coating, and sealing electronic assemblies. It excels at bonding dissimilar substrates with different coefficients of expansion and has a wide service temperature range of -60ºF to 250ºF.

LISTED UNDER: Epoxy | Epoxy | Seals and Gaskets
Advertisement

Spot Curing System Offers Flexibility

April 6, 2010 5:08 am | Product Releases | Comments

Utilizing the latest in UV LED technology, this spot curing system provides a peak irradiance of 9,500 mW/cm², with a lifetime of over 20,000 hours. It offers the ability to control up to four UV LED heads simultaneously with a single connection or independently.

LISTED UNDER: UV-or Light-Cure

Spot Curing System Offers Flexibility in UV Assembly Applications

February 5, 2010 10:55 am | Product Releases | Comments

EXFO Photonic Solutions (MD&M West Booth 2209) has introduced the OmniCure LX400 UV LED Spot Curing System, which utilizes the highest power and most reliable LED technology in one of the smallest form factors currently available for UV adhesive curing.

LISTED UNDER: UV-or Light-Cure

Adhesive Pairs with LED Lamp for Fast Medical Device Assembly

January 22, 2010 10:59 am | Product Releases | Comments

The 1020-M Ultra Light-Weld is an ultra-fast, tack-free, LED-curable adhesive. It's designed for rapid bonding of a wide variety of plastics typically used in the manufacture of medical devices, such as reservoirs, tube sets, port fittings, drug delivery systems, and heat-sensitive applications.

LISTED UNDER: UV-or Light-Cure | Fittings

No-Drip Medical Adhesive Designed for Bonding Vertical Surfaces

December 2, 2009 4:28 am | Master Bond, Inc. | Product Releases | Comments

The EP42HT 2 ND 2 has a paste like consistency and facilitates the adhesive's application when bonding vertical surfaces. This no-run two part epoxy fully complies with the testing requirements for USP Class VI biocompatibility.

LISTED UNDER: Epoxy | Biocompatibility Testing | Microbiology/Chemical Testing

New Silicone Gel Tape & Chip Vibration Isolators

November 23, 2009 9:36 am | Product Releases | Comments

Advanced Antivibration Components (AAC)’s Silicone Gel Tape & Chip Vibration Isolators, identified as the V10Z62MGT and V20Z62MGC Series, are designed for light to medium loads. The gel tape is stocked in 1000 mm lengths and in 3 thicknesses: 1 mm, 2 mm and 3 mm.

LISTED UNDER: Tapes

Medical Portfolio Desk Reference for Converters and OEMs

October 5, 2009 6:19 am | Product Releases | Comments

Converters of medical materials and manufacturers of medical device components can now turn to an artfully designed desk reference from the Avery Dennison Specialty Tape division for medical tape selection assistance.

LISTED UNDER: Tapes

UV Cure Adhesive With Bond Strength

September 8, 2009 12:51 pm | Master Bond, Inc. | Product Releases | Comments

Master Bond adds a strength advantage to a UV adhesive compound combining high strength bonds with the well established benefits of UV cure: high productivity, improved performance, and environmental compliance.

LISTED UNDER: UV-or Light-Cure

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading