Advertisement

Antireflection Coatings

February 28, 2007 10:46 am | Edmund Optics | Product Releases | Comments

The high-quality Tech Spec family of optical components has been enhanced by adding a visible, antireflection coating option to its plano-convex, plano-concave, double-convex, double-concave, and achromatic lines. The coating features an average reflectance of less than 0.

LISTED UNDER: Device Coating
Advertisement

Conformal Coating Jet

February 28, 2007 10:46 am | Asymtek | Product Releases | Comments

The SC-400 PreciseCoat conformal coating jet is designed for applying coating materials to highly selective areas, especially on small substrates or substrates with high-component density where there are tight tolerances between coated and uncoated areas.

LISTED UNDER: Dispense | Device Coating

Motion Control Coating

January 18, 2007 11:36 am | Kerk Motion Products | Product Releases | Comments

Superior performance lead screw, linear rail, spline shaft, and ScrewRail actuator assemblies are all offered with Kerkote TFE coating.

LISTED UNDER: Ball and Lead Screws | Device Coating

Fastener Coating

December 5, 2006 12:21 pm | Nylok Corp. | Product Releases | Comments

There is no need for gasket seals or sealant compounds or any other time-consuming in-house assembly sealants.

LISTED UNDER: Fasteners | Device Coating

Low Cost Motor Resolves Coating Challenge

December 5, 2006 12:19 pm | Elliptec Resonant Actuator Ag | Product Releases | Comments

After an introduction of the basic technology of the Elliptecmotor, this article will present the physical analysis necessary for understanding the operation of the motor and will discuss its use in vacuum conditions. The technology can be utilized to address concerns with physical vapor deposition.

LISTED UNDER: Permanent Magnet Motors | Actuators | Wire and Cable

Vinyl Coating

August 8, 2006 12:51 pm | Caplugs | Product Releases | Comments

The ability to vinyl coat wheelchair handles, handlebar grips, and anything else that needs to have a soft, ergonomic finish molded to is available.

LISTED UNDER: Device Coating

Hydrophobic Coating

July 10, 2006 10:13 am | G&L Precision Die-Cutting, Llc-A Lohmann Co. | Product Releases | Comments

A hydrophobic coating for plastics was designed to compliment the company’s proprietary diagnostic adhesive, GL-187. The coating can be successfully applied to polyester, polystyrene, vinyl, and other plastics for IVD and a variety of other medical applications.

LISTED UNDER: Device Coating | Device Coating

Temporary Masking Resin

February 8, 2006 5:57 am | Product Releases | Comments

The SpeedMask 7100 series of temporary metal masking resins offer reliable surface protection for orthopedic implants, implant hardware, surgical instruments, and medical devices. These masking resins cure in seconds using UV light.

LISTED UNDER: Device Coating

Complex Coatings

February 8, 2006 5:57 am | Edmund Optics | Product Releases | Comments

Company has increased its capacity to make complex coatings with more than 100 layers, by adding a new 45-inch-diameter coating chamber. The large coater is equipped with two electron guns and planetary rotation. It also has a high output ion gun, which produces durable “shift-free” coatings.

LISTED UNDER: Device Coating | Device Coating

Optical Coating Service

February 8, 2006 5:57 am | Melles Griot | Product Releases | Comments

Company will make its thin-film coating capability available to customers who need optical coating services for their own substrates.

LISTED UNDER: Device Coating | Device Coating

High Performance Coatings

February 8, 2006 5:57 am | Boyd Coatings Research, Inc. | Product Releases | Comments

As a licensed applicator of advanced technologies such as Dupont Teflon and Whitford Worldwide

LISTED UNDER: Device Coating | Device Coating

Gravure Coating

February 6, 2006 10:29 am | Product Releases | Comments

Scapa has the ability to gravure coat adhesives in a cross-hatch pattern onto a wide range of substrates. This pattern coating reduces the amount of adhesive on the substrate and allows strategic areas to be left uncoated to achieve specific performance requirements.

LISTED UNDER: Device Coating | Device Coating

Emphasis on Coatings:Processing Considerationsfor Surface Modification Technologies

November 1, 2005 11:32 am | SurModics, Inc. | Product Releases | Comments

Performance, manufacturability, safety, and overall cost are crucial when selecting coating technologies, while ease of application, use of hazardous solvents, cycle time, and scrap rates are key when evaluating a coating’s manufacturing process.

LISTED UNDER: Device Coating | Surface Modification Coatings | Surface Modification

PTFE Coating

September 30, 2005 11:43 am | Point Technologies, Inc. | Product Releases | Comments

Promising high lubricity, superior chemical resistance, and excellent electrical insulating characteristics, PTFE is available to be selectively coated onto small diameter wire components such as pins, needles, and electrodes as well as plain wire.

LISTED UNDER: Device Coating | Device Coating

Polymerized Thin Film Coatings

August 11, 2005 10:41 am | Plasmatech, Inc. | Product Releases | Comments

Contract processing services for thin film coatings and gas plasma surface treatment offer a variety of beneficial features.

LISTED UNDER: Device Coating | Hydrophilic Coating | Device Coating

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading