Advertisement
Product Releases
Subscribe to MDT Magazine Product Releases
View Sample

FREE Email Newsletter

MDT Daily

Linear Actuator (3613)

December 5, 2006 12:21 pm | Comments

This linear actuator is designed for positioning requirements in a variety of applications, including medical. It is lead screw driven and provides an electromechanical alternative to a pneumatic actuator, improving accuracy and motion control.

Surface Mount Resistors (3605)

December 5, 2006 12:21 pm | Comments

Providing design engineers with rugged surface mount devices specifically designed for surge/pulse applications and for circuits subject to extreme thermal cycling, this company offers two versions of its popular cylindrical surface mount resistors.

Low Cost Motor Resolves Coating Challenge

December 5, 2006 12:19 pm | Comments

After an introduction of the basic technology of the Elliptecmotor, this article will present the physical analysis necessary for understanding the operation of the motor and will discuss its use in vacuum conditions. The technology can be utilized to address concerns with physical vapor deposition.

TOPICS:
Advertisement

Parallel Buses Give Way to Serial Point-to-Point Interconnects

December 5, 2006 12:19 pm | Comments

As medical equipment becomes more advanced, the demands on the electronic components are increasing exponentially. Large amounts of data are being collected during various tasks and systems need to be able to handle it.

TOPICS:

Sterile Packaging Sought as Solution for Infection Prevention

December 5, 2006 12:19 pm | Comments

Trends being observed now in medical device manufacturing are expected to create an increase in the demand for sterile packaging through 2010, according to a report from The Freedonia Group. This article summarizes the findings of the group’s study.

TOPICS:

Software Solutions: Building Blocks for FDA Compliance

December 5, 2006 10:48 am | Comments

Many medical device manufacturers have discovered that their choice of ERP

NIH Grant Could Help Patients Breathe Easier

December 4, 2006 5:16 am | Comments

Quest Product Development, with partner University of Colorado, has completed Phase I research

TOPICS:

Knee Implants Smarten Up

December 4, 2006 5:16 am | Comments

Orthopedic implants keep getting smarter. For the first time, a patient has received an investigational, full artificial knee replacement that can wirelessly report digital, 3D torque and force data back to computers.

Advertisement

ScopeMeter/Divider Kit

December 4, 2006 4:39 am | Comments

The 199XRAY Medical ScopeMeter and 35080M Non-Invasive kVp Divider kit combination significantly streamlines x-ray system calibration, QA, or corrective maintenance procedure setup and analysis.

TOPICS:

Custom Tubing Assemblies

December 4, 2006 4:39 am | Comments

Known for tubing and fitting capabilities, the company also customizes tubing assemblies for specific OEM instruments and applications. It offers a comprehensive selection of tubing in capillary through large-bore sizes, with ODs from less than 0.0145 to 5/16 in.

Power Supply (3585)

December 4, 2006 4:39 am | Astrodyne Corporation | Comments

Two series of ultra-miniature, open-frame modular switching power supplies are available. In a small mechanical footprint measuring only 2 in. W x 4 in. L x 1.2 in. H, both the ASM40 and ASM60 series provide power densities &gt6 W/in 3 .

TOPICS:

Amorphous Polymers

December 4, 2006 4:39 am | Comments

Extem thermoplastic polyimide (TPI) resins are a family of amorphous polymers that provide exceptional performance while eliminating the drawbacks of semi-crystalline materials.

MDT EXCLUSIVE: Noise Filters

December 4, 2006 4:39 am | Comments

The NAM series is a diversified line of noise filters. With 6 current options (4, 6, 10, 16, 20,

Panelmount Socket

December 4, 2006 4:39 am | Comments

The reduced footprint 713 series M12 male sockets allows fastening from the back side of a panel and reduces the required surface area for mounting. The design features an M12 rear thread allowing the connector to be mounted to a panel having a thickness of up to 3.0 mm.

Injecting Design Into the Molding Process

November 10, 2006 10:24 am | Comments

There are a number of factors medical device manufacturers need to consider when using injection molded parts in their device. If they don’t, they may be caught by surprise when they think they are ready to move into full production on a part.

Pages

X
You may login with either your assigned username or your e-mail address.
The password field is case sensitive.
Loading